Sunday, 2 October 2016

“หลายหลากคำถามเกี่ยวกับ CT Current Transformer” Questions about CT

สวัสดีท่านผู้อ่านที่น่าฮักค่ะ….ในฉบับนี้เราจะมานำเสนอเกร็ดความรู้ที่เกี่ยวกับ  Current Transformer  ที่เรามักได้ยินปุถุชนส่วนใหญ่ขนานนามกันว่า CT
Lovato Electric Current Transformer
CT  เป็นอุปกรณ์ที่ใช้ประกอบการวัดกระแสไฟฟ้าโดยต่อร่วมกับเครื่องวัดกระแส โดยทำหน้าที่แปลงกระแสไฟฟ้าที่วัดให้เหมาะสมกับพิกัดกระแสไฟฟ้าที่ขดลวดกระแสของเครื่องวัด เช่น 100/5   500/5  เป็นต้น

อะไรคือ Ratio ของ CT

Ratio คืออัตราส่วนของการแปลงกระแส จากกระแสด้าน primary เป็นกระแสด้าน  secondary เช่น ratio ของ CT 300 : 5 มีความหมายว่า ‘CT มี rated primary current เท่ากับ 300 A และ rated secondary current มีค่า 5A’

ข้อควรระวังของ Current Transformer!

Safety Warning about Current Transformer
ห้าม Open Circuit ด้าน Secondary ของ CT ในขณะที่มีกระแสไหลผ่านขดลวดของ CT ด้าน Primary เด็ดขาด!!!

ที่กล่าวมาข้างต้นคือ ข้อมูลพื้นฐานของ CT ต่อจากนี้เราจะมาตอบคำถามที่ผู้ใช้งานหลายท่านค้างคาใจกันอยู่ เริ่มกันเลยนะคะ

ปุจฉา  “หากใช้ CT เกินหรือต่ำกว่าค่าพิกัดกระแสที่กำหนดจะส่งผลอย่างไร???”
วิสัชนา  จริงๆแล้วต้องบอกว่า CT นั้นจะมี “accuracy ที่ดีที่สุดเมื่อใช้งานเต็มพิกัด” นั่นหมายความว่า หาก CT  100/5 ก็ควรใช้งานที่ 100 A จะดีสุด แต่หากว่าไม่ได้ใช้งานตามนั้น ค่า Accuracy ก็จะเพี้ยนเปลี่ยนไป ดังตารางต่อไปนี้
จากตารางสามารถยกตัวอย่างประกอบคำอธิบายได้ว่า
–          หากเลือกใช้  CT  :   Class  0.5  , 100/5 A
กรณีใช้ที่พิกัด 100 %  (100 A)  >  ค่า Accuracy จะยังคงเป็น 0.5 เท่าเดิม
กรณีใช้ที่พิกัด 20 %  (20 A)  >  ค่า Accuracy จะเปลี่ยนเป็น 0.75
กรณีใช้ที่พิกัดเกิน 100 % (ใช้กับกระแสมากกว่า 100 A)  >  ค่า Accuracy นั้นไม่สามารถบอกได้เลยค่ะ TT
ปุจฉา                    แล้วจากข้างต้นมีวิธีการแก้ไขอย่างไร???
วิสัชนา                   ไม่เป็นปัญหาค่ะ เรามีวิธีแก้กล่าวคือ   หากเรามี CT 100/5 A   แต่!!!เราต้องการใช้กับกระแสเพียง 20 A  ก็ไม่ต้องลำบากไปหาซื้อ CT ใหม่นะคะ เพียงแต่พัน CT  ที่ฝั่ง primary  100/20 = 5 รอบ เพียงเท่านั้น ก็สามารถใช้ CT ตัวเดิมได้โดยไม่ต้องเสียเงินซื้อใหม่แล้ว และหากว่าจะใช้ที่ค่ากระแสอื่นๆก็ยังทำได้นะคะ ดังตาราง
ค่ากระแสที่ต้องการวัด
จำนวนรอบการพัน
100
1
50
2
25
4
10
10
ยกเว้นกรณีที่ต้องการใช้ CT เกินค่ากระแสที่กำหนด เช่น มี CT 100/5 แต่ต้องการใช้กระแส 150 A กรณีแบบนี้ไม่สามารถใช้ได้นะคะ


Lovato Electric black Current Transformer
Example of Split Core and Solid Core Current Transformer from Lovato Electric. Available Online from Factomart.com. Click on the image to visit the website.


ปุจฉา                ค่า Burden คืออะไรเอ่ย
วิสัชนา                   ค่า Burden หมายถึง กำลังไฟฟ้าของหม้อแปลงกระแสไฟฟ้า โดยถ้าอุปกรณ์ไฟฟ้าทุกตัวที่ต่ออนุกรมกับขด secondary มีกำลังไฟฟ้าสูญเสียในเครื่องวัดรวมกำลังไฟฟ้าสูญเสียในสายวัดมีค่าภายใต้เบอร์เดนของหม้อแปลงไฟฟ้าแล้ว ความผิดพลาดจากการวัดจะเป็นไปตามคลาสของหม้อแปลงกระแสไฟฟ้านั้น
นั่นคือ       กำลังไฟฟ้าสูญเสียในเครื่องวัด  +  กำลังไฟฟ้าในสายวัด + ….   <    กำลังไฟฟ้าสูญเสียของ CT
Current Transformer Application
ที่กล่าวมาข้างต้นเป็นคำถามที่พบบ่อยๆ    นอกจากนั้นแล้วก็ขอนำเสนอความรู้เพิ่ม นั่นคือมี Current Transformer แบบพิเศษที่ใช้กับการตรวจจับกระแสรั่วลงดินเรียกว่า Zero current transformer (ZCT)   หลักการก็คือ จะต้องนำ R, S, T, N ผ่านตัว ZCT ทั้ง 4 เส้น หากไม่มีกระแสส่วนหนึ่งส่วนใดรั่วไหลออกไปที่อื่นก็จะทำให้ผลรวมของกระแสสามเฟสจะเป็น 0 จะไม่มีกระแสไฟฟ้าที่หลงเหลือไปที่ Earth-Leakage Protection Relay (ไม่สั่งทริป) แต่ถ้าหากมีกระแสปริมาณหนึ่งไหลออกจากนอกระบบ(ลงที่โครงตู้หรืออื่นๆ)จะทำให้ผลรวมของกระแสไม่เท่ากับ 0 จะมีกระแสไหลไปที่ Eartleakage relay ถ้าปริมาณมากเกินที่ตั้งไว้ ก็จะสั่งให้ Main-circuit breaker ทริปทันที

Thursday, 15 October 2015

Method to select bolt size

Method for calculating Stud Bolt lengths
The Stud Bolt theoretical length can be calculated
by means of the formula: L = 2 (s + n + h + rf) g
Method for calculating Stud Bolt length
  • s = free threads (equals 1/3 time bolt diameter)
  • n = nut height (equals nominal bolt diameter)
  • h = flange (plate) thickness
  • rf = height of raised face
  • g = gasket thickness
Method for calculating Stud Bolt lengths for flanged connections

Thursday, 2 October 2014

The 18 best Outlook tips

The 18 best Outlook tips for increasing productivity: become an Outlook expert with these lesser-known tips

Posted on 30 May 2014 at 12:29
Want to become an Outlook expert? Here are the 18 best Outlook tips that can make handling your email and appointments quicker and easier
Millions of people use Microsoft Outlook to manage their email and calendar, at work and at home. That’s a testament to its usefulness – but the truth is that few of us really know how to make the most of its features. Learning a few simple tricks can save you time, help you work more efficiently and synchronise home and work life. These tips are geared towards Outlook 2007, 2010 and 2013, but many also apply to Outlook 2003 and earlier.

Best Outlook tips: 1. Spare yourself repeated typing with Quick Parts

If you regularly need to trot out a standard passage of text, you can save it as a Quick Part for easy insertion into your emails. Simply highlight the text in the composer window, then switch to the Insert tab, click the Quick Parts dropdown and select “Save selection to Quick Parts gallery”. In future, when you start typing the phrase, you’ll see it pop up as a suggestion – hit return to insert it in full. You can also select your text with the mouse from the Quick Parts dropdown. Right-click on it for placement options, or to edit and manage Quick Parts and other “building blocks”.

Best Outlook tips: 2. Write a message to be delivered at a future time

The 18 best Outlook tips
If you have some news that you don’t want to share immediately, Outlook lets you defer delivery until a specified time. Write your email, then switch to the Options tab and click Delay Delivery. This opens a requester with a “Do not deliver before:” field; enter a date and time, then click Close. After you hit Send, the message will be held until the specified time for sending. If you’re using an Exchange server, you can now close Outlook; if you’re using POP or IMAP you’ll have to leave the application open until the specified time for delivery has passed.

Best Outlook tips: 3. Group messages by…

If you receive a high volume of email, tracking down relevant messages can be a chore. Outlook can group emails into conversations, so that a single click shows all related messages together. You can set this on a global or per-mailbox basis by going to the View tab and ticking “Show as Conversations”. Click the “Arrange By:” bar at the top of the message list and select “View Settings...” from the dropdown menu to configure additional grouping options.

Best Outlook tips: 4. Create a folder for common searches

You can always search the current folder by typing into the search field above the message list. If there’s a particular search you frequently carry out, you can simplify the job with a Search Folder. Go to the Folder tab and click New Search Folder to create one: you can choose from a variety of templates (such as finding mail from specific people, or mail marked as important) or set up your own criteria using the “Create a custom Search Folder” option. Your new search folder appears in the folders pane at the left-hand side of the Outlook window; click on it to see messages meeting your selected conditions. Right-click and select Rename Folder to give it a convenient name.

Best Outlook tips: 5. Filter emails to find relevant messages

The 18 best Outlook tips Filter
Another quick way to find specific emails is to use the Filter Email dropdown at the far right of the Home tab. Choosing a menu option instantly filters your mailbox display to show only certain types of emails, such as those with attachments, those dated within a specific time period and so forth. Within your filtered view, you can type into the regular search box to drill down further.
For more search options, select “More Filters…” from the dropdown to make the Search Tools tab visible: here you’ll find additional settings, as well as the Recent Searches dropdown that lets you repeat recent searches with a single click.

Best Outlook tips: 6. Junk or Ignore unwanted email

If someone keeps clogging up your inbox, you can block all future email from that sender by clicking the Junk dropdown on the Home tab. Select “Junk E-mail Options” to open a configuration dialog that lets you specify what you count as junk and what you don’t – here you can blacklist entire domains and even entire countries. If the sender is legitimate but the conversation isn’t relevant, click Ignore: this doesn’t permanently block anyone, but new emails in that particular conversation thread will be binned as soon as they arrive.

Best Outlook tips: 7. Instantly create new emails and appointments

The 18 best Outlook tips appointments
If you make full use of Outlook’s features, you may find yourself frequently switching back and forth between email and calendar modes. Regardless of whether you’re looking at your inbox or your calendar, you can create new emails, appointments, contacts and so forth using the New Items dropdown on the Home tab. If you don’t want to delve into the Outlook interface, right-click on Outlook’s icon in the Windows 7 or 8 taskbar to open a jumplist offering direct shortcuts to create any sort of new item.

Best Outlook tips: 8. Automate recurrent tasks with Quick Steps

If you find yourself regularly performing a particular task – such as forwarding an incoming email to a colleague, or inviting a group of recipients to a meeting – then Quick Steps can save you time. You’ll find a set of predefined Quick Steps in the middle of the Home tab, but the real power of the feature comes in defining your own. Click the dropdown arrow and select New Quick Step to create a custom sequence of actions that can categorise, move, flag and delete messages with a single tap of your mouse. Clicking on “Manage Quick Steps…” opens a dialog from which you can duplicate and edit shortcuts, so you can create a range of variations on a theme.

Best Outlook tips: 9. Sort your mail with Rules and Conditional Formatting

The Rules dropdown in the Move section of the Home tab provides options to create and manage rules for automatically processing messages as they arrive. If you select a message before clicking, it will offer to create a rule affecting similar messages. Select Create Rule and you’ll be given the option to set all sorts of criteria to check for – sender, recipient, size, date and more – and choose what should happen to matching emails.
The 18 best Outlook tips email
A similar feature is Conditional Formatting, which you’ll find under View Settings on the View tab. This doesn’t move or process messages, but it displays emails matching certain criteria in a specified font and colour, so you can instantly spot them in your inbox.

Best Outlook tips: 10. Send text messages from within Outlook

When email won’t cut it, Outlook supports sending SMS text messages directly to your contacts. You’ll need to register with a third-party messaging service to use this feature, however, and if you want to send more than a handful of text messages you’ll inevitably have to pay. To set up SMS, click the New Items dropdown under the Home tab, select Text Message (SMS) and, in the dialog that opens, click “Find a text messaging service for your mobile operator”.

Best Outlook tips: 11. Automatically clear out unneeded messages

If you want to save space or tidy up an unwieldy email trail, the Clean Up tool in Outlook 2010 and 2013 can help. It analyses a complete email conversation and deletes any messages that have been quoted in their entirety inside a subsequent message – the logic being that you can still see what’s been said by checking subsequent messages.
To use Clean Up, click its dropdown on the Home tab and choose whether you want to tidy up a single conversation or a whole folder. Click the Settings button in the alert that opens to choose what sort of messages should be culled and what should be left alone.

Best Outlook tips: 12. Delegate access to your mail and calendar

If you’re going away, you can temporarily let someone else manage your inbox and appointments. To set this up, open the File tab (or the Orb in Outlook 2007), then click the Account Settings dropdown and select Delegate Access. Click Add and enter the name of the person (or people) to whom you want to grant access. You’ll see a set of dropdowns for permissions: by default, your delegate can access and update your calendar and task list, while email and contacts remain private.
Note that your delegate must be using the same version of Outlook as you, and the items you want them to access must be stored on an Exchange server: they won’t be able to get at a mailbox that lives on your hard drive.

Best Outlook tips: 13. Manage read receipts

Happily, Outlook is well-behaved enough to ask permission before sending a read receipt; you can customise its behaviour further by clicking on the File tab, opening Options, selecting the Mail view and scrolling down to the Tracking section. Here you can choose whether receipts should be sent always, or never, and you can also configure your own receipt request settings. One useful option is the ability to request a delivery receipt, which confirms your email has reached the recipient’s mail server, without insisting on a notification when it’s actually opened.

Best Outlook tips: 14. Time zones

If you travel for work, you’ll know the frustration of finding meetings and appointments in Outlook show up at the wrong local time. Under File | Options | Calendar you’ll find the option for setting your local time zone: once you’ve done this, email timestamps and calendar entries will be shown with the appropriate offset.
You can also configure a second time zone to be shown so that (for example) you can keep track of what time it is back home, or see what time it is for your colleagues overseas, to ensure you catch them during office hours and don’t contact them at an inconvenient time of day. Click Swap Time Zones to easily switch from one location to the other.

Best Outlook tips: 15. “Post-it” notes

Outlook includes a built-in sticky notes feature. Press Ctrl+Shift+N from anywhere in the Outlook interface to create a new note, which can be dragged and positioned anywhere on screen. By default, notes appear in pale yellow, but you can assign them to categories, which causes them to switch to the associated colour. To manage your notes, click on the Note icon at the bottom of the View pane: From here you can copy, organise and print notes, and also search, via the field at the top-right of the window, for notes containing specific text.

Best Outlook tips: 16. Encrypted email

The 18 best Outlook tips Encrypted email
If you want to prove your messages are really from you, Outlook can cryptographically sign your emails. You can even go a step further and encrypt the text and attachments, so that only recipients with whom you’ve shared the key can read them. To set this up, open the Trust Center Settings (you’ll find the button under File | Options | Trust Center) and click on E-mail Security. Enabling digital signing and encryption is as easy as ticking the relevant boxes, but you’ll need to create and import a digital ID if you don’t already have one. Click “Get a Digital ID…” to see links to a range of providers, including Comodo, which offers free email certificates.

Best Outlook tips: 17. Access your personal email within Outlook

To add a personal mailbox to Outlook, go to the File tab and click Add Account to open the wizard: if you’re using a web service such as Gmail or Yahoo Mail, check the provider’s instructions for setting up access via POP or IMAP. If you’re using Outlook.com with Outlook 2013, simply enter your email address and Outlook will handle the rest.
To access Outlook.com mail from earlier versions of Outlook, click “Manually configure server settings or additional server types”, then select the Microsoft Outlook Hotmail Connector from the window that opens. This lets you access not only your webmail but also your personal calendar from within Outlook.

Best Outlook tips: 18. Sync Google Calendar with Outlook

In Google Calendar, move your mouse over your calendar in the left-hand pane, click on the dropdown that appears and select Calendar Settings. Click Private Address | ICAL to obtain the URL of your calendar’s iCal feed. Now, in Outlook, go to File | Account Settings | Account Settings…, click on the Internet Calendars tab and paste the URL into the dialog that opens. After a few minutes the calendar will start to update and your events will appear in Outlook. If you want to make Outlook events appear in Google Calendar, you’ll need a third-party tool: One option is gSyncit by Fieldston Software, which offers a free trial version that lets you sync one Google calendar with one Outlook calendar.
Author: Darien Graham-Smith


Read more: The 18 best Outlook tips for increasing productivity | Analysis | Features | PC Pro http://www.pcpro.co.uk/features/388939/the-18-best-outlook-tips-for-increasing-productivity-become-an-outlook-expert-with-these-lesser-known-tips#ixzz3F3eKc0CM

Thursday, 5 June 2014

Tresca and Von mises stress

Brief explanation from my current understanding

Tresca purpose that "ductile" material will fail(yield) when maximum shear stress exceed shear yielding (ty)
Q1-Q3 >Qy,
ty=Qy/2

Von mises strain energy density reaches a critical value
wd ≥ wyd

Wednesday, 9 April 2014

windload


Wind Pressure


The design of the structure's primary lateral force system, as well as its elements and components, shall be based upon wind pressures determined from the following equation:


P = Ce Cq qs I
where
P = design wind pressure in psf.



  1. Qs = wind stagnation pressure in psf at a height of 33' above the ground.
    • This wind force is a function of wind velocity:
      • Qs = .00256 V2
        Wind Stagnation Pressure
        Wind stagnation pressure is based upon Bernoulli's equation and its a function of the wind velocity squared and the mass density of air. The UBC equation assumes a standard air density of 0.0765 pcf and does not account for density changes as the result of altitude, season of the year, weather, and latitude.


        where V = windspeed in mph found from UBC Figure 16-1.
        • The applicable wind speed map can be found as Figure 2-1 in the article Nature of Wind
      • Can also find Qs using UBC Table 16-F.
      • The minimum design speed is taken as 70 mph.
        • Refer to Wind Speeds for information relating windspeeds in mph to observations.
      • V is based upon the 50-year mean recurrence interval for the fastest-mile wind speeds.
    50-Year Mean Recurrence Interval
    This means that the probability of experiencing a basic wind speed faster than the indicated value in any one-year period is one in fifty of 2%.Fastest-Mile Wind Speeds

    In the U.S. wind speeds are measured by recording the time a constant number of turns of the anemometer occur equivalent to one mile of wind passing by.
    Other countries use different windspeed measuring methods. This results in different reported values for similar intensity winds.
  2. Iw = Importance factor taken from UBC Table 16 - K.
    • Essential facilities and hazardous facilities are designed to withstand higher forces by setting Iw = 1.15, which is approximately equivalent to a 100 year recurrence interval.
    • Otherwise, Iw = 1.0

  3. CE = combined height, exposure, gust coefficient found in UBC Table 16 - G.
    • Wind pressure increases with building height:
      • For the windward wall, UBC uses a stepped pressure diagram as f(height).
      • For the leeward wall, pressure taken as constant over the full wall height and is calculated using the mean roof height for CE determination.
    • Turbulence (gusting) = f(terrain), is quantified in terms of an exposure rating:GustingThis component accounts for the effects of air turbulence and dynamic building behavior. The underlying gust response assumptions are only appropriate for structures that have stiffness, mass, and damping characteristics similar to ordinary buildings with a period of vibration less than one second. More flexible structures may experience wind effects that are substantially greater than that predicted by UBC; particularly with respect to the across-wind response.
      Exposure Effects
      Ground surface irregularities and flow obstructions such as trees and other buildings reduce wind forces. The UBC broadly categorizes these terrain influences through the use of exposure ratings.

      Although a building site may have different exposure in different directions, the most severe exposure governs for all wind load calculations.

      • B - urban, suburban, closely spaced obstruction the size of single - family residences.
      • C - open country and grasslands that are generally flat.
      • D - unobstructed flat terrain facing a large body of water extending inland 1/4 mile or ten times building height, whichever is greater.
      • UBC recognizes only 3 of the 4 possible exposure classes.
        • It has not adopted Exposure A - building sites in large city centers.

  4. Cq = Pressure coefficient.
    • Found in UBC table 16 - H.
    • Cq = f (structure or part of, analysis method, openings)
    • Structure or part of:
      • Cq for primary LFRS.
        LFRSThe lateral force resisting system (LFRS) is that part of the structural system designed to resist lateral loads. For bearing wall type building considered here, the horizontal diagrams and the shear walls make up the LFRS.
        • Considering the whole structure as it resists lateral forces.
        • Applied to horizontal diaphragms and shearwalls.
      • Cq for elements and components:
        • Accounts for higher pressures that occur locally.
        • Taken at locations away from discontinuities, and
        • At discontinuities.
    • Primary frame analysis methods:
      • Method 1: normal force method

        • A more accurate description of wind forces.
        • Windward and leeward forces acting normal to all exterior surfaces simultaneously.
      • Method 2: the projected area method.
        • Carry over from earlier codes.
        • Simpler than method 1.
        • Generally more conservative.
        • Cannot be used for gabled rigid frames or structures greater than 200' in height.
        • Simultaneous application of horizontal pressures on the vertical projected area and vertical pressure on the horizontal projected area.
    • Openings:
      • Open (known as partially enclosed in newer codes like the '94 and '97 UBC's) structures have higher outward pressures than enclosed or unenclosed structures.
      • Doors and windows are considered openings unless protected.
      • Account for the effect of openings in partially enclosed buildings by using a bigger Cqcoefficient according to footnote 1 Table 16 - H.
        Footnote 1, Table 16-H
        1For one story or the top story of multistory partially enclosed structures, an additional value of 0.5 shall be added to the outward Cq. The most critical combination shall be used for design. For definition of open structures, see section 1613.
        • This effect could be simply thought of as what happens to the surface of a balloon as it is being blown up.
        • For primary LFRS, method 1: increase Cq for roofs according to footnote 1 of UBC 16-H.
      • For elements and components not at discontinuity: select Cq according to the element under consideration, and if building is unenclosed, enclosed, or partially enclosed.
      • Definitions, according to '97 UBC 1616, for enclosed, partially enclosed, and unenclosed:
        • Aoi = area of opening on projected side i.
        • Ai = total projected wall area of side i.
        • Aoj = area of opening on projected side j.
        • If Aoi / AI ³ 0.85 for all sides, then structure is unenclosed.
        • If Aoi / AI > 0.15 for side i and if
          S Aoj < .5 Aoi for all other sides j, then structure is partially enclosed.
        • All other cases, consider the building as enclosed.


Wind Loads

Building Stability



  • In addition to the design of the primary load-resisting system and the individual elements with respect to wind pressures, the entire structure must be checked for overturning.
  • This phenomenon can be simply described by considering an empty cereal box located in front of a household fan.

  • Without proper connection to the table, the box will act like a rigid body; overturning by rotating and falling about its far corner.
  • Similarly, you need to ensure moment stability of the entire structure and those elements that are part of the LFRS, (e.g. shearwalls).
  • According to '94 UBC 1619.1, or '97 UBC 1621.1
    '94 UBC 1619.11619.1 General. The primary frames or load-resisting system of every structure shall be designed for the pressures calculated using Formula (18-1) and the pressure coefficients, Cq, of either Method 1, or Method 2. In addition, design of the overall structure and its primary load-resisting system shall conform to Section 1603.

    The base overturning moment for the entire structure, or for any one of its individual primary lateral-resisting elements, shall not exceed two thirds of the dead-load-resisting moment. For an entire structure with a height-to-width ratio of 0.5 or less in the wind direction and a maximum height of 60 feet (18,290 mm), the combination of the effects of uplift and overturning may be reduced by one third. The weight of the earth superimposed over footings may be used to calculate the dead-load-resisting moment.
    , the overturning moment (OM) must be £ 2/3 of the resisting moment (RM) due to dead loads.
    • But if h/b £ 0.5, h £ 60', and the entire structure OM accounts for both lateral and uplifting loads, then may use OM £ RM.
  • Consider the simple model of our building in terms of the cereal box.
    OM = Ph + U b/2
    RM = D b/2
    If OM ³ 2/3 RM, then hold corner A down with an anchor capable of resisting a tensile force of:
    T = (OM - 2/3 RM) / b.

  • In addition to checking the entire structure, you need to also check each shearwall as modeled below.

    • If all shear walls are adequate wrt OM, surely the entire structure will be adequate.
    • With other structural systems it is common practice to check overturning of the entire building, but with a conventional shearwall building the practice is to check each shearwall instead.


Wind Loads

Building Drift



  • Another important consideration in building design is to examine the structure's potential for movement due to lateral loads. This is known as building drift, Ds, or more specifically story drift.
  • UBC doesn't limit story or building drift due to wind, but does for seismic in UBC '94 1628.8 or '97 UBC 1630.10
    • Story drift - lateral displacement of one level relative to level above or below.

  • General guidelines suggest limiting Dwind:
    D £ (.0025) h as applied to masonry shear walls.
  • Shearwall behavior is a function of shearwall length, L, to height, h, considerations.





Wind Loads

Example


Develop the applicable wind forces for a one-story, box-type industrial complex located in Southern California, in a suburban area with roof D = 12 psf and 16" o.c. partially grouted CMU walls.






  1. Design pressure for primary LFRS:

    For this example, the pressure coefficients are the same regardless of load direction.

    P = Ce Cq qs Iw
      qs Þ V = 70 mph (Figure 16-1, UBC '97)
        qs = 12.6 (UBC '97 Table 16-F)

      Iw = 1.0 (UBC '97 Table 16-K)

    Ce Þ Exposure B Þ{.62(0 - 15')(UBC '94 Table 16-G)
    .67(20')

    CqÞMethod 1
    (Table 16-H)
    Þ{.8 windwardAssuming » flat roof and closed building.
    -.5 leeward
    -.7 roof

    The resulting pressure diagram for wind loading in the transverse direction:

  2. Diaphragm Loading:
    • Showing transverse loading here.
    • Consider a 1' width of wall that is simply supported at foundation and roof.
    • Examine the normal wall load effect on the supporting diaphragm:
      • Since the diaphragm must support both, simultaneously, the inward and outward pressures, model these effects as a resultant pressure.


    • The roof diaphragm must resist 125.4 lb/ft (or, in other words, each foot of wall produces a force of 125 lbs on the diaphragm.)

  3. Diaphragm to shear walls for flexible diaphragms:
    • Showing only the transverse loading.
    • We will only work with flexible diaphragms in this class.

    Diaphragm Plan View:



    In this example, the shear wall at each end must resist a resultant load of 7837.5 lbs.

  4. Upon development of the shear wall loads, examine shear wall drift and overturning.
    1. Shear wall drift:
      • L/h = 66/17 = 3.88, drift dominated by shear deflection.
      • Therefore during wall design, ensure that D » 1.2 P h / G A £ .0025 h
    2. Overturning (OM)
      • Since this is a shear wall building, every shear wall should be checked for OM.
      • Check all shear walls, in lieu of an overall building OM check (In other words, if the shear walls are adequate then the overall building is adequate. But, remember that overall building stability does not ensure that all shear walls are ok).



        RM = Resisting Moment
        RM = 87120 (33) = 2,874,960 ft-lbs
        OM = Overturning Moment
        OM = 7837.5(17) = 133,240 ft-lbs
      • If the shear wall supported a significant % of the roof framing, then a portion of roof uplift should be included in OM. Likewise, a portion of the roof dead load should be included in RM.
      • 2 / 3 RM = 1,916,640 > > OM
      • No special anchorage required for the shear wall, which is typical for masonry walls that support wood roof systems. (This is not, however, true for all wood buildings with wood shear walls. Very often, these lightweight walls will need special hold down anchors to resist the overturning potential.)

  5. Lateral forces normal to the wall.
    • In addition to acting as shear walls, these walls must be designed to resist forces acting perpendicular to them.
    • These perpendicular forces do not come from the primary LFRS analysis as shown in step 1. Develop these forces by considering localized, higher loads taken on portions of the building as reflected in Cq.
    • A careful reading of '97 UBC Table 16-H indicates two load cases here.
      • One for all structures and the other for enclosed and unenclosed structures.
      • For outward (negative) forces, use Cq/Ce based on mean roof heights.
      • For inward (positive) forces, use Cq/Ce based on the actual height of the element.

  6. Repeat wind load development and distribution for wind in longitudinal direction.

Tuesday, 18 March 2014

RunAsDate

www.nirsoft.net
RunAsDate is a small utility that allows you to run a program in the date and time that you specify

Overload Devices

http://www.lpc.rmutl.ac.th/elcen/elearning/motorcontrol/module6/overload.html

 หลักการ
       ในสภาพการใช้งานมอเตอร์จะต้องเกิดความร้อนขึ้น
อย่างหลีกเลี่ยงไม่ได้ ความร้อนที่เกิดขึ้นเนื่องมาจากสาเหตุ
หลายประการเช่น อุณหภูมิแวดล้อม กระแสเนื่องจากการ
ใช้งาน กระแสเกินเนื่องจากมอเตอร์รับภาระมากเกินไป
หรือภาวะโหลดเกิน (Overload) สาเหตุเหล่านี้ทำให้มอเตอร์
เกิดความเสียหายขึ้นได้ วิธีการป้องกันมอเตอร์โดยการใช้
โอเวอร์โหลดจึงเป็นวิธีการที่ใช้ในการป้องกันมอเตอร์ที่
นิยมใช้กันทั่วไป
จุดประสงค์
1. บอกประเภทของความร้อนที่เกิดขึ้นกับมอเตอร์ได้ถูกต้อง
2. บอกประเภทของโอเวอร์โหลดได้ถูกต้อง
3. อธิบายการทำงานของโอเวอร์โหลดได้ถูกต้อง
4. บอกเปอร์เซ็นต์การปรับตั้งโอเวอร์โหลดได้ถูกต้อง
5. คำนวณค่ากระแสของการปรับตั้งโอเวอร์โหลดได้ถูกต้อง
คำแนะนำ :  1. ศึกษาจากเนื้อหาด้านล่างนี้
                          2. 
ทำแบบฝึกหัดประจำโมดูลที่ 6
                          3. ทำแบบทดสอบท้ายโมดูลเพื่อประเมินตนเองในการเข้าศึกษาในโมดูลที่ 7 ต่อไป

6.1 ความร้อนที่เกิดขึ้นกับมอเตอร์
     ความร้อนที่เกิดขึ้นกับมอเตอร์มีสาเหตุหลายประการ
เช่น


- จำนวนกระแสของโหลด
- ระยะเวลาของการมีโหลดเกิน
- ความถี่บ่อยในการสตาร์ทมอเตอร์
- เวลาที่ใช้ในการสตาร์ทจนมอเตอร์ถึงความเร็ว
   สูงสุด
- อุณหภูมิแวดล้อม (Ambient temperature)
- ความสามารถในการระบายความร้อน
- ช่วงเวลาในการทำงาน (Duty cycle)
     ดังนั้นจึงมีความจำเป็นอย่างยิ่งที่ควรจะต้อง
ทำการติดตั้งโอเวอร์โหลดที่มีขนาดเหมาะสมใน
อุปกรณ์สตาร์ทมอเตอร์ เพื่อทำการป้องกันมอเตอร์
จากการเกิดโอเวอร์โหลด หรือความร้อนเกินพิกัด
ซึ่งจะส่งผลต่ออายุการใช้งานของมอเตอร์ได้


6.2 โอเวอร์โหลดทำงานด้วยความร้อน(Thermal Overload Relay)
     โอเวอร์โหลดประกอบด้วยขดลวดความร้อน
(Heater) พันอยู่บนแผ่นไบเมทัล (Bimetal) ซึ่งทำ
จากโลหะ 2 ชนิดเชื่อมติดกันโก่งตัวได้เมื่อเกิด
ความร้อนขึ้น ขดลวดความร้อนเป็นทางผ่านของ
กระแสจากแหล่งจ่ายไปยังมอเตอร์ เมื่อกระแส
ที่ไหลเข้ามอเตอร์มีค่าสูง ทำให้ชุดขดลวดความร้อน
เกิดความร้อนสูงขึ้น เป็นผลให้แผ่นไบเมทัลร้อน
และโก่งตัวดันให้หน้าสัมผัสปกติปิดของโอเวอร์โหลด
ที่ต่ออนุกรมอยู่กับวงจรควบคุมเปิดวงจร ตัดกระแส
ออกจากคอล์ยแม่เหล็กของคอนแทกเตอร์ จึงทำให้
หน้าสัมผัสหลัก (Main Contact) ของคอนแทกเตอร์
ปลดมอเตอร์ออกจากแหล่งจ่ายเป็นการป้องกัน
มอเตอร์จากความเสียหายได้

     โอเวอร์โหลดรีเลย์มีทั้งแบบธรรมดา คือ เมื่อ
แผ่นไบเมทัลงอไปแล้วจะกลับมาอยู่ตำแหน่ง
เดิม เมื่อเย็นตัวลงเหมือนในเตารีด กับแบบที่มี
รีเซ็ท (Reset) คือ เมื่อตัดวงจรไปแล้ว หน้าสัมผัส
จะถูกล็อกเอาไว้ ถ้าต้องการจะให้วงจรทำงานอีกครั้ง
ทำได้โดยกดที่ปุ่ม Reset ให้หน้าสัมผัสกลับมาต่อ
วงจรเหมือนเดิม


สัญลักษณ์ของโอเวอร์โหลดรีเลย์แบบมี Reset

   ลักษณะเมื่อเกิดการโอเวอร์โหลดหน้าสัมผัส
จะเปิดออกและจะถูกล็อกเอาไว้ ถ้าต้องการให้
ต่อวงจรต้องกดที่ปุ่ม Reset อีกครั้ง

    โดยปกติแล้วการปรับตั้งขนาดกระแสโอเวอร์-
โหลด มีค่าเท่ากับ 125 % ของกระแสโหลดเต็มพิกัด
(Full Load Current หรือ FLA) ของมอเตอร์ เช่น
มอเตอร์มีกระแสโหลดเต็มพิกัดเท่ากับ 40 แอมป์
ดังนั้นค่าสูงสุดของการปรับตั้งโอเวอร์โหลดมีค่า
เท่ากับ
10 x 1.25 = 12.5 แอมป์ (A)
     โอเวอร์โหลดโดยทั่วไปมีปุ่มปรับตั้งพิกัดกระแส
ให้ทำการปรับโดยใช้ไขควงปรับด้านหน้าของ
โอเวอร์โหลด เช่น 9, 10, 11, 14, 16, 18 แอมป์
เป็นต้น (ดังรูป)


รูปโอเวอร์โหลดรีเลย์ที่เป็นส่วนหนึ่งของชุดสตาร์ทมอเตอร์

รูปโอเวอร์โหลดรีเลย์ในมุมมองต่าง ๆ

รูปแสดงปุ่มปรับตั้งกระแสทริปของโอเวอร์โหลดรีเลย์

คลิ๊กเพื่อดูการทำงาน
รูปโครงสร้างภายในของโอเวอร์โหลดรีเลย์
(ใช้เมาส์วางบนรูปภาพ และคลิ๊กเพื่อดูการทำงาน)